回流焊参数 | | | | |
型号MODEL | VS-800II / NS-800II | VS-1000II / NS-1000II | VS-800IIX / NS-800IIX | VS-1000IIX / NS-1000IIX |
机体参数GENERAL | | | | |
外型尺寸(L*W*H) Outside Dimension(L*W*H) | 4820x1350x1490mm | 6100x1353x1490mm | 5310x1580x1490mm | 6100x1580x1490mm |
颜色Standard Color | 计算机灰Computer Grey | 计算机灰Computer Grey | 计算机灰Computer Grey | 计算机灰Computer Grey |
重量Weight | Approx.2250KG | Approx.2450KG | Approx.2350KG | Approx.2550KG |
加热区数量Number Of Heating Zones | 上Up8/下Bottom8 | 上Up10/下Bottom10 | 上Up8/下Bottom8 | 上Up10/下Bottom10 |
加热区长度Length Of Heating Zones | 3200mm | 3891mm | 3121mm | 3891mm |
冷却区数量Number Of Cooling Zones | 2(内置) |
排风量要求Exhaust Volume | 10 M3 / min x 2 (通道) Exhausts |
控制部分参数Standard Feature Of Control System |
电气要求Electric Supply Required | 3 phase,380V 50/60Hz(optional: 3 phase,220V 50/60Hz选配) |
电源功率要求Electric Power Required | 35KW | 40KW | 45KW | 50KW |
启动功率Power For Warm Up | 30KW | 36KW | 32KW | 38KW |
正常功率消耗Power Consumption | 8KW | 10KW | 12KW | 14KW |
升温时间Warming Time | 约Approx.25 minute | 约Approx.35 minute |
温度控制范围Temp. Setting Range | 室温Room Temp. --- 300℃ |
温度控制方式Temperature Control Method | PID闭环控制+ SSR驱动/ PID Close Loop Control + SSR Driving |
温度控制精度Temperature Control Precision | ± 1.0℃ |
PCB板温分布偏差Temperature Deviation on PCB | ± 1.5℃(by JT Board Test Standard) |
加热器Heating Element | Especial Heating elements For Long Life ;特制的特长寿命加热器 |
Commutated Element整流板结构 | Aluminium Alloy Plate铝板 |
Max. Temp. Gap Between Preheat & Reflow Setting
预热区和焊接区之间的最大温度设定差值 | 80℃ |
Max. Temp. Gap Between Preheat Zones Setting
预热区之间的最大温度设定差值 | 40℃ |
Max. Temp. Gap Between Reflow Zones Setting
焊接区之间的最大温度设定差值 | 50℃ |
参数存储Data Storage | 可存多种生产设置参数与状况Process Data and Status Storage (80GB) |
异常报警Abnormal Alarm | 温度异常（恒温后超高温或超低温）Abnormal Temperature (Extra-high / Extra-low Temp.) |
掉板报警Board Dropped Alarm | 三色信号灯:黄-升温；绿-恒温；红-异常Tower Light: Yellow–Warming; Green-Normal; Red-Abnormal |
运输参数Standard Features Of Conveyor System | |
导轨数量 | 1 Lane | 2 Lanes |
Rail Structure导轨结构 | Subsection Integrated Type整体分段式Subsection Separate Control分段独立控制(Option选配) |
PCB最大宽度Max.Width Of PCB | 400mm (Option:610mm选项) | A and B lanes width each 250mm or 1 lane 450mm and other lane 50mm |
导轨调宽范围/调宽形式 | 50--400mm(Option:50--610mm选项)/电动Motorized | 50--450mm/电动Motorized | (相关A、B线的宽度组合请参考上一栏) |
RangeOf RailWidth/Adjustment | (Width relate to A&B, please refer item above) |
部品高度Components Clearance | PCB板上/下各25mm , Top/ Bottom Clearance of PCB is 25mm |
运输方向Converyor Direction | 左向右(选配:右向左) L→R (Option: R→L) |
运输导轨固定方式Fixed Rail Side | 前端固定(选配:后端固定)Front Rail Fixed(Option:Rear Rail Fixed) | 前后导轨固定，中央两条活动. Front and Rear Rails Fixed, 2 adjustable Rail at central. |
PCB运输方式PCB Transmission Agent | 空气炉Air-Reflow =链条+网带Chain + Mesh ,氮气炉N2-Reflow =链条Chain (可选配网带Mesh is option) | | | |
中央支撑Center Support (选配Option) | 防止PCB板因过宽及元器件过重而弯曲变形Preventing PCB warp such too wide and heavy component load |
运输带高度Converyor Height | 900±20mm |
运输速度Converyor Speed Range | 300～2000mm/min |
Lubrication Auto-Afflux润滑油自动加注 | Standard |
回流热工学管理分析Thermal Management System and Analysis System | |
KIC RPI焊接质量检测系统KIC RPI Reflow Process Inspection | 只标配于VS系列, Standard for VS-series only |
Temp. Thermocouple Slot
温度曲线测试线 | 4 |
Electrical Driven Top Hood Opening
电动打开上温区盖 | 标准配置Standard |
Operation Mode: Operate / Demo / Edit
三种操作模式:运行/演示/编辑 | 标准配置Standard |
On Line Editing在线编辑功能 | 标准配置Standard |
Cooling Method冷却方式 | Forced-Air空气冷却(标配Standard), Water-Chiller冷水冷却(选配Option) |
带氮气系统机型Model for Nitrogen Process | VS-800II-N / NS-800II-N | VS-1000II-N / NS-1000II-N | VS-800IIX-N / NS-800IIX-N | VS-1000IIX-N / NS-1000IIX-N |
电源功率要求Electric Power Required | 67KW | 83KW | 67KW | 83KW |
启动功率Power For Warm Up | 32KW | 38KW | 34KW | 40KW |
正常功率消耗Power Consumption | 13KW | 15KW | 14KW | 16KW |
正常耗氮量Nitrogen Consumption | 20M3/hr. @ 300ppm~1000ppm (O2浓度/ O2 Concentration) ;氮气流量计with N2 Flow Rate Meter |
助焊剂管理Flux Management System | 氮气炉膛标配空气循环过滤，优化炉内环境，易于维护保养。Flux Reclaimed and Filtration standard for N2 Oven, easy clean-up. |
N2 containment at Entry and Exit End
入口及出囗氮气保护装置 | 标准配置Standard |
Flux Reclaim System
助焊剂回收系统 | 标准配置Standard |
Nitrogen Flow Meter氮气流量计 | 标准配置Standard |
Oxygen Analyser氧气分析仪 | 选配Option |
Nitrogen Consumption [Standard]
氮气消耗量(标准) | 400~1000PPM 20M³/H |
Nitrogen consumption [Dilated hearth]
氮气消耗量(加宽机) | 500~1000PPM 25~30M³/H |
冷水机Water Chiller | 3 HP ;外置式External Stand-alone Type ;充足冷却能力满足无铅工艺要求Powerful Cooling suit to Lead-Free Process Required |
| | | | |
注明：氮气机在尾号为"-N"的设备才是标配, Standard for N2 Oven Model With suffix of "-N" | | |
点击图片查看大图
